Certification IntroductionIC is the abbreviation of Industry Canada. As a government agency, it is responsible for the certification of electrical and electronic products entering the Canadian market. Its responsible products are roughly divided into: radio and television equipment, information technology equipment, radio equipment, telecommunication equipment, engineering and medical equipment, etc. Similar to the FCC in the United States, ICs currently only limit electromagnetic interference.Certification CategoryThere are two ways of self-verification and certification. IC ID: CN (Company Number, up to 6 digits) + UPN (Unique Product Number, up to 8 digits).Instructions for IC ID application:1. Must have Canadian representative address information. 2. The label should contain the following information (manufacturer's name or trademark, model name, IC ID number).application process1. The manufacturer or agent submits an oral or written preliminary application to the certification company. 2. The applicant fills in the application form, sends the application form, product instruction manual and technical documents to the certification company, and also provides a prototype if necessary. 3. The certification company draws up plans and quotes. 4. The applicant confirms the quotation, signs the quotation back, and sends the samples and related technical documents to the certification company. 5. The applicant provides technical documents. 6. The certification company issues a fee notice to the applicant, and the applicant prepays the certification fee according to the fee notice. 7. The certification company reviews the technical documents and organizes relevant certification activities. 8. If the technical documents are incomplete or the specified language is not used, the certification company will notify the applicant to improve. 9. If the test fails, the certification company will promptly notify the applicant and decide whether to suspend the project, allowing the applicant to improve the product. The applicant should make changes to the technical data in the original application so as to reflect the actual situation after the changes. 10. For the rectification fees involved in Articles 9 and 10 on this page, the certification company will issue a notice of supplementary fees to the applicant. 11. The applicant shall pay the rectification fee according to the requirements of the supplementary fee notice. 12. The certification company provides the applicant with test reports or technical documents and certificates. IC ID certification steps 1 to 12 are equivalent to IC certification 13, the test report and data are submitted to the FCB/TCB agency for review and certification.Application information1. Instructions in English 2. Specifications 3. Circuit schematic diagram 4. PCB board diagram 5. Block diagram 6. Business license 7. Organization code 8. Application form 9. Product pictures 10. Samples

Certification IntroductionCSA is the abbreviation of Canadian Standards Association. It was established in 1919 and is the first non-profit organization in Canada to formulate industrial standards. Electronics, electrical appliances and other products sold in the North American market are required to obtain safety certification. CSA is currently the largest safety certification body in Canada and one of the most famous safety certification bodies in the world. It can provide safety certification for all types of products in machinery, building materials, electrical appliances, computer equipment, office equipment, environmental protection, medical fire safety, sports and entertainment. CSA has provided certification services for thousands of manufacturers around the world, and hundreds of millions of products bearing the CSA mark are sold in the North American market every year.Applicable areaBefore 1992, CSA-certified products could only be sold in the Canadian market, and products that wanted to enter the US market had to obtain relevant US certification. CSA International has been recognized by the U.S. federal government as a Nationally Accredited Testing Laboratory. This means your products can be tested and certified to Canadian and U.S. standards, while ensuring your certification is recognized by federal, state, provincial and local governments.application process1. Complete the preliminary application form, and submit it to CSA together with the instructions and technical data of all related products (including all electrical components and plastic materials); 2. CSA will determine the certification fee according to the specific conditions of the product, and then notify the applicant company; 3. After being confirmed by the applicant company, a formal application form and a notice will be sent. The notice includes the following requirements: (1) After the formal application form is signed, the certification fee (which can be paid in RMB) will be sent to the office. (2) Send the test sample to the designated location as notified. 4. The designated laboratory will carry out the certification work on time. 5. After the certification test is completed, a preliminary report will be issued to the applicant company, with details as follows: (1) How the product structure needs to be improved to meet the standard (2) Other information to be used to complete the certification report (3) Please The content of the draft record of the applicant company's contract certification (4) Marks required for CSA certification and the method of obtaining the marks (5) Factory testing required for the product 6. CSA will evaluate the applicant's answer to the fifth item above; 7. At the same time CSA will prepare a certification report for product production reference and follow-up inspection. 8. At this stage, in some cases, CSA will go to the factory for initial factory evaluation, referred to as IFE. 9. Finally, CSA will issue a certificate of conformity together with the certification record, authorizing the applicant company to add the CSA certification mark on other products. 10. The applicant company should sign a service agreement with CSA to indicate that both parties agree that CSA will go to the factory for product follow-up inspection. The applicant company is required to pay an annual fee each year to maintain the agreement.Application information1. Company information sheet, copy of business license 2. Product description (including but not limited to the following): 3. Product name, product model, and product use. 4. For the parts list, please provide the name and model, rating and manufacturer information of the product parts. If the part has been certified by CSA or UL, please indicate the file number of the part. If there are multiple suppliers for a part, it can be provided. 5. Product performance and specifications, such as size, rated voltage, current, frequency and power, etc. 6. Structural drawing or exploded drawing: The structural drawing of the product shall indicate the name of the part in the drawing, so as to correspond one-to-one with the parts list. 7. Provide circuit schematic diagram: PCB schematic diagram, product photos, instructions for use, safety matters or installation instructions, etc.

Certification IntroductionThe NOM mark is a mandatory safety mark in Mexico to indicate that the product complies with the relevant NOM standards. The NOM logo applies to most products, including telecommunications and information technology equipment, household electrical appliances, lamps and other products that are potentially hazardous to health and safety. Whether it is locally manufactured or imported in Mexico, it must comply with the relevant NOM standards and product labeling regulations.The Normas Oficiales Mexicanas sign is a mandatory safety sign in Mexico to indicate that the product complies with the relevant NOM standards. The NOM logo applies to most products, including telecommunications and information technology equipment, household electrical appliances, lamps and other products that are potentially hazardous to health and safety. Whether it is locally manufactured or imported in Mexico, it must comply with the relevant NOM standards and product labeling regulations.Under Mexican law, the licensee of NOM must be a Mexican company responsible for the quality, maintenance and reliability of the product. The test report is issued by a laboratory accredited by SECOFI and reviewed by SECOFI, ANCE or NYCE. If the product meets the relevant regulatory requirements, a certificate will be issued to the Mexican representative of the manufacturer or exporter, and the product can be marked with the NOM mark.Mandatory Authentication Mode- M0: certification by quality control and periodic test verification; - M1: certification by periodic test verification (new product type experiment); - M2: certification by quality system evaluation and verification (new product); - M3: Letter of conformity issued by periodic test verification (for new products); - M4: Certification by quality control and periodic test verification (for redesigned products); - M5: Batch certification (Applicable to redesigned products and used products without redesign manual); - M6: 100% certification (applicable to non-standard products). The certificate holder is usually a separate importer, manufacturer and distributor, and foreign manufacturers can apply for a certificate through a certification body recognized by the Mexican Standardization Committee.Applicable product scopeProducts subject to NOM compulsory certification are generally electrical and electronic products with a voltage exceeding 24 volts of alternating current or direct current. Mainly used in the fields of product safety, energy and heat effects, installation, health and agriculture. The following products must obtain NOM certification before they are allowed to enter the Mexican market: 1. Electronic or electrical products for home, office and factory use; 2. Computer LAN equipment; 3. Lighting devices; 4. Tires, toys and school supplies; 5. Medical equipment; 6. Wired and wireless communication products, such as wired telephones, wireless telephones, etc.; 7. Products powered by electricity, propane, natural gas or batteries.application process1. Find a third-party testing agency to provide services; 2. Send at least two samples to the testing agency for testing; 3. Provide all product information (Spain); 4. Provide certification applications to testing agencies; 5. Provide Mexican distributors or importers name and address.Application documents1. Application form 2. Authorization letter 3. Registration documents of local importers or distributors 4. Relevant CB certificates and reports 5. Instructions for use in Spanish (requirements include quality assurance certificates) 6. Technical documents (circuit diagrams, general assembly diagrams, Parts list) or CB (including Mexican deviation) 7. Service Manual 8. Company Profile (English) 9. Parts Supply GuaranteePackaging Label Information1. Name and address of importer or distributor 2. NOM logo 3. Original domestic information 4. Product input/output rating 5. Product name and model 6. Packing quantity NOM certification lead time4-6 weeksMexico only recognizes its own NOM safety signs, and the safety signs of the United States and Canada (such as CUL, ETL, CSA) are not recognized by the government of that country. Products requiring compulsory certification can enter the Mexican market only with the NOM safety mark. Normally, the NOM logo often appears together with NYCE or ANCE: ——NOM NYCE: applicable to electronic products, communication products and data processing equipment, but excluding household appliances; ——NOM ANCE: applicable to household electrical appliances, including household electrical appliances, Electric hand tools, etc.

Certification IntroductionTUV Süd cTUVus certification is the North American certification mark of TUV Süd. As long as it has been accredited by OSHA (Occupational Safety and Health Administration) as a testing and certification body of NRTL (National Recognized Testing Laboratory), it can conduct testing and certification services for products entering the US and Canadian markets. Qualified in the same way as other NRTL agencies (e.g. UL, CSA), thus helping products successfully enter the US and Canadian markets. All NRTL marks (cTUVus, UL, CSA, ETL, cNEMKOus) are equivalent. As an authorized laboratory of the TUV Süd, ITL can carry out testing of cTUVus certification for products according to customer needs, and issue test reports. Difference between cTUVus, UL and ETL certification projectULcTUVusETLuse standardUL2054; UL1642; UL61558; UL62368.1 (the combined standard of UL60950 and UL60065), etc.Certification accreditation bodyUS NRTL (Nationally Recognized Laboratory) and Standards Canada SCCCertification MarketNorth America (US and Canada)Certification and Testing OrganizationUL laboratory tested and issued a Notice of Authorization(NoA)ITL test TUV certificationITL test ITS certificationApplication time reference5-12 weeks2-3 weeks2-3 weeksapplication feeMore expensive than the othersThe cost is more favorableThe cost is more favorableAdvantageNative American organization, the most recognized old-fashioned certification organization in the United States and CanadaInternational certification body, authoritative and inexpensive, also recognized by NRTL in the United StatesNative American institutions, highly recognizeddisadvantageBecause it is an old-fashioned institution, the testing, factory inspection and file fees are the highest, and the cycle is long.North American market brand awareness is slightly lower than ULThe North American market reputation is slightly lower than UL

Certification IntroductionThe cTUVus Verified Mark provides customers with a clear and straightforward approach to product safety, enabling their products to successfully enter the US and Canadian markets., Germany TUV Rheinland has been registered in North America, and can perform the verification and product testing services of the American ANSI/UL standard and the Canadian national standard.Technical InformationFrequency: 60Hz Voltage: Single-phase 120V (used in the United States and Canada, measuring between fire and ground, providing 15 or 20A protection line); 240V (measuring between water and fire, generally available)Voltage: Three-phase 208/240VPlug Construction: US and Canada use NEMA 5-15P and 6-15P plug standards. These straight blade plugs in the US are clearly described in NEMA (National Electronics Manufacturers Association) WD6 edition and incorporated into UL498. Canadian plug and socket standards are referred to in CSA publication C22.2, No.42.Applicable product scopeThe authorized projects of TUV Rheinland include: office equipment, information technology, business machines, audio-visual equipment, home appliances, laboratory equipment, medical equipment, testing and measuring devices, and control equipment, etc.The US and Canada certification marks of TUV Rheinland are of the same level as other US NRTL (like UL, CSA, etc.). TUV Rheinland issues TUVus verification mark for products in the US marketTUV Rheinland issues cTUV verification mark to products in the Canadian marketWhen the TUVus and cTUV logos are used together, customers can place a single logo, cTUVus, on a product to prove that the product meets the required standards for both the US and Canada markets.Difference between cTUVus, UL and ETL certificationprojectULcTUVusETLuse standardUL2054; UL1642; UL61558; UL62368.1 (the combined standard of UL60950 and UL60065), etc.Certification accreditation bodyUS NRTL (Nationally Recognized Laboratory) and Standards Canada SCCCertification MarketNorth America (US and Canada)Certification and Testing OrganizationUL laboratory tested and issued a Notice of Authorization(NoA)ITL test TUV certificationITL test ITS certificationApplication time reference5-12 weeks2-3 weeks2-3 weeksapplication feeMore expensive than the other agencyThe cost is more favorableThe cost is more favorableAdvantageNative American organization, the most recognized old-fashioned certification organization in the United States and CanadaInternational certification body, authoritative and inexpensive, also recognized by NRTL in the United StatesNative American institutions, highly recognizeddisadvantageBecause it is an old-fashioned institution, the testing, factory inspection and file fees are the highest, and the lead time is long.North American market brand awareness is slightly lower than ULThe North American market reputation is slightly lower than UL

Certification IntroductionThe full name of the FCC is the Federal Communications Commission, established in 1934 by COMMUNICATION ACT, it is an independent agency of the U.S. government and is directly accountable to Congress. The FCC coordinates domestic and international communications by controlling radio, television, telecommunications, satellite and cable. Involving more than 50 states in the United States, Columbia and the United States In order to ensure the safety of radio and wire communication products related to life and property, the FCC Engineering and Technology Department is responsible for the technical support of the committee and is responsible for equipment approval. Many radio application products, communication products and digital products require FCC approval to enter the US market. Authentication typeOn November 2, 2017, the FCC merged DoC and Verification into SDoC (Supplier's Declaration of Conformity). SDoC certification will replace the FCC Verification and DoC certification procedures. All equipment applicable to the FCC Verification and DoC certification procedures are taken by SDoC certification procedures. The FCC has two different certification methods for the types of electronic products: FCC SDoC and FCC ID (Certification). The former is suitable for ordinary products without wireless functions, and the latter is suitable for products with wireless functions.Comparison between FCC SDoC and FCC IDFCC SDoCFCC IDApplicable ProductsOrdinary products without wireless functions, such as display screens, lamps, etc.Products with wireless functions, such as mobile phones, Bluetooth headsets, etc.Test contentElectromagnetic Compatibility EMCElectromagnetic compatibility EMC+RFCertification feeLowhightest periodshortlong Applicable product scope1. Power supply: communication power supply, switching power supply, adapter, wireless charging, charger, display power supply, LED power supply, LCD power supply, UPS, etc.;2. Lamps: ceiling lamps, wall lamps, chandeliers, track lamps, garden lamps, portable lamps, down lamps, street lamps, string lights, table lamps, floor lamps, grill lamps, aquarium lamps, energy-saving lamps, LED street lamps, LED desk lamps, LED floor lamps, LED ceiling lights, LED spotlights, LED bulbs, LED tubes, LED lamps, energy-saving lamps, T8 lamps, etc.;3. Household appliances: refrigerators, washing machines, electric fans, tower fans, bladeless fans, air-conditioning fans, mobile air conditioners, humidifiers, dehumidifiers, clothes dryers, clothes dryers, air purifiers, fresh air systems, vacuum cleaners, cleaning machines, Mite removal machine, sweeping robot, air conditioner, range hood, dishwasher, electric oven, disinfection cabinet, integrated stove, commercial kitchen equipment, electric water heater, air energy water heater, electric hot water faucet, water purifier, water dispenser, juicer , juice maker, wall breaker, coffee maker, bread maker, electric oven, air fryer, egg beater, electric stew pot, cooking machine, rice cooker, yogurt maker, noodle maker, electric pressure cooker, soy milk maker, Microwave oven, induction cooker, electric ceramic cooker, electric cake stand, electric kettle, hair dryer, beauty instrument, facial cleanser, hair curler, hair straightener, hair clipper, shaver, oral care, epilator, massage chair, massager, weight scales, etc.;4. Electronics: TV, audio, power amplifier, DVD, VCD, projector, camera, monitor, computer, server, scanner, printer, copier, earphone, mouse, keyboard, router, mobile phone battery, laser pointer, etc.;5. Communication products: telephones, fax machines, telephone recorders, data machines, data interface cards and other communication products.6. Wireless products: Bluetooth BT products, tablet computers, wireless keyboards, wireless mice, wireless readers, wireless transceivers, wireless walkie-talkies, wireless microphones, remote controls, wireless network devices, wireless image transmission systems and other low-power wireless products Wait;7. Wireless communication products: 2G mobile phone, 3G mobile phone, 3.5G mobile phone, 4GS mobile phone, Internet card, DECT mobile phone (1.8G, 1.9G frequency), wireless walkie-talkie, etc.;8. Machinery: gasoline engine, electric welding machine, CNC drilling machine, tool grinder, lawn mower, washing equipment, bulldozer, elevator, punching machine, dishwasher, water treatment equipment, gasoline welding machine, printing machinery, woodworking machinery, rotary Drilling rigs, lawn mowers, snow blowers, excavators, printing presses, printers, cutters, road rollers, trowels, brush cutters, hair straighteners, food machinery, lawn machines, etc.;FCC common standardsAs follows, FCC PART 15 and PART 18 are the most widely used:FCC standard application scopeFCC PART15 C/E/F Intentional Radiation Device TestFCC PART 18 Industrial, Scientific and Medical EquipmentFCC PART 22 Public Mobile Communication ServicesFCC PART 24 Personal Communication ServicesFCC PART 25 Satellite Communication ServicesFCC PART 27 Other FCC wireless communication servicesFCC PART 68 Telecommunications Terminal EquipmentFCC Part 15 regulates transmitting equipment that is intentional, unintentional, or transient and does not require a personal license for use. It includes technical specifications, administrative requirements and other market access conditions. Products are mainly divided into four categories: unintentional launch equipment, intentional launch equipment, license-free personal communication equipment, and license-free national basic information equipment.FCC Part 18 regulates the emission of electromagnetic energy by industrial, scientific, and medical equipment (ISM) operating on a certain frequency spectrum to avoid harmful interference to authorized wireless communication services.application process1. The customer submits the application form to the testing agency; 2. The customer prepares testing samples (wireless products require a fixed frequency machine), and provides product information (see data requirements); 3. The testing agency issues a draft report, the customer confirms, and issues a formal report; 4. If it is an FCC sDoC, the project is completed; if it is an application for an FCC ID, submit a report and technical data to TCB; 5. After the TCB audit is completed, the FCC ID certificate is issued, and the testing agency sends an official report and FCC ID certificate; 6. The enterprise obtains the FCC ID certificate. After certification, you can use the FCC logo and related Statements on the product; Note: Manufacturers applying for FCC ID certification for the first time need to register with the FCC for FCC-FRN to establish an application company file. The certificate issued after the TCB audit completed will have FCC ID Number, usually FCC ID is composed of "Grantee code" + "Product code". Manufacturer code: It is a three-digit number or capital letter, issued directly by the FCC; Product code: It is composed of numbers, letters, and "-", but there cannot be two or more consecutive "-" used, the first and last digits can not use "-", the maximum number of digits in this code is no more than 14 digits, and the number can be customized by the customer.Application documents1. User manual 2. Block Diagram 3. Operation Description 4. Circuit schematic 5. RF modulation mode RF modulation 6. Rated Power Declaration 7. Application form TCB Form 731 8. Authorization Letter POA 9. FCC Confidential Letter Note: The list of materials and requirements to be submitted for FCC ID certification are as follows: (1) FCC application form: application company name, address, contact information, product name and model, usage standards and other information requirements; (2) FCC authorization letter: it must be signed and stamped by the contact person of the applicant company and scanned into an electronic file; (3) FCC confidential letter: the confidential letter is an agreement signed by the applicant company and the TCB agency to keep product information confidential , to be signed and stamped by the contact person of the applicant company and scanned into an electronic file; (4) Block diagram: All crystal oscillators and the frequency of the crystal oscillator need to be drawn and consistent with the circuit diagram; (5) Circuit diagram: It must be the same as the one in the block diagram. The frequency of crystal oscillator, the number of crystal oscillators and the position of crystal oscillator are the same; (6) Line description: the requirement is in English, and the function realization principle of the product is clearly described; (7) Instruction manual: FCC Statement is required; (8) Label and label position: the label must be There are FCC ID numbers and Statements, and the location of the label is required to be obvious; (9) Photos of the inside and outside of the product: the pictures are required to be clear and clear, and remarks are added if necessary; (10) Test report: the test is required to be completed, and the product is fully evaluated according to the standard terms;